Sometimes manufacturers will credit a mechanic or repair shop to replace parts of the engine or completely rebuild the entire thing. From there, the manufacturers will take further action if the tests prove the buyer’s claim to be valid. In most cases, owners are advised to drive the vehicle for a minimum of 1000 miles and then return it to the manufacturer, where they run tests to determine if excessive oil consumption is present. However, some Toyota consumers experience up to 0.5 liters of consumption every 1000 miles.
Japanese manufacturers like Toyota say a quart for every 1000 to 1200 miles is fine. They can elude responsibility because oil consumption is determined based on manufacturer standards. Many such brands will say that the level at which the engine is consuming oil is perfectly normal. The engine winds up taking in more oil down the guides and into the cylinders as a side effect of worn, broken, or poorly installed guide seals.Įxcessive oil consumption is one of the problems shared by many major car manufacturers other than Toyota. Oil Consumption ProblemsĮxcessive oil consumption happens when there is too much clearance between the valve stems and guides. The fix, however, is priced from $1500 to $2500. The parts can cost anywhere from $30 to $150. Of course, the safest and best bet is to take the car to a mechanic. Note that piston replacement is a complicated procedure. Just ensure that the engine loses compression before you attempt to replace the pistons.
The most obvious solution is to replace the piston as well as the rings. This is the knocking sound you may hear while the car is running or idling. Since they have a vast wall clearance, to begin with, more speed only results in the piston rocking. When pistons experience cold clearance, they gain more speed. Generally, the piston does need to perform this up and down movement, but when the motion becomes involuntary, the piston begins rocking. This sort of knocking occurs when the piston is being forced up and down the cylinder. The kind of motor knocking we are referring to here is the type that occurs due to a failing piston and is more likely to happen in aluminum blocks. – 11.8:1 – 1UR-FSE Computable Vehicles for 1UR engineĬommon Toyota 4.6 Engine Problems and Solutions 01. 10,000 miles (15,000 km) / 12 months is the Oil change interval.Naturally aspirated Four-stroke internal combustion engine.Cylinder block and the head is made from Aluminium.Manufactured by Toyota Motor Corporation.Four-into-one (4-1) stainless steel headers in the exhaust system.Hydraulic lifters included with valvetrain.Roller rocker arms activate exhaust and intake valves.Water-cooled Exhaust Gas Recirculation (EGR) system.Aluminum alloy cylinder block with cast-iron liners.Acoustic Control Induction System (ACIS).Electronic Throttle Control System – intelligent (ETCS-i).Fuel efficiency estimates of 15 mpg city and 20 mpg on the highway.Timing chains used instead of unreliable timing belts.Other features of the Toyota 4.6 engine include: The 1UR (Toyota 4.6 engine) incorporates incredible injection technology with the tried-and-true Toyota dual VVT-i system and V8 formation.
The Toyota 4.6l engine is the product of masterful engineering, ten steps ahead of the old 2UZ-FE engine. They are facilitated by the twelve-hole fuel injectors and done in the fashion of L-type fuel injections. In typical Toyota fashion, the system runs the camshafts, the Direct Ignition System (DIS), Acoustic Control Induction System (ACIS), and Electronic Throttle Control System – intelligent (ETCS-i). The engine is equipped with Toyota’s Dual VVT-i system. Said camshafts manage the exhaust camshafts through the usage of a secondary timing chain on each head. Timing chains propel the intake camshafts. Instead of timing belts, the 4.6 engine has timing chains. While the cylinders maintain their typical V8 formation, the aluminum cylinder heads now come with two camshafts and four valves per cylinder. Due to the decrease in balance weights, the Toyota 4.6 engine runs noticeably less smoothly than the previous version. The Toyota 4.6 engine crankshaft has six balance weights, two less than its forerunner. The Toyota 4.6 engine is on a roll for its usage of solid metals as they crafted their spark plugs out of the highly long-lasting iridium metal.
The cylinder has four oil jets for the sole purpose of using oil to keep the pistons cool. This is one of the more notable improvements present in the 1UR engines that the previous model lacked. The incredible thing is that these cylinders are made from a metal known for their durability and longevity- aluminum. As a V8 engine, the Toyota 4.6 engine has the requisite eight cylinders in the “V” formation.